|
|
| Register | FAQ | Members List | Calendar | Mark Forums Read |
|
#1
03-29-2005, 05:38 PM
|
|||
|
|||
|
apexi avc-R fitment
Hi folks
I've just ordered an apexi avc-r boost controller,which i am going to fit to my Evo VI gsr when it arrives  I have been searching for info regarding the fitment of it. Has any of you fitted one before? if so is it imperative you wire it into the ecu? im not too bothered about having all the diffrerent settings that can be programmed into it,i basically just want it to set my boost level!!! So if anyone has any experience with this unit your input would be appreciated!!!! 
|
|
#2
03-29-2005, 05:51 PM
|
|||
|
|||
|
Is the unit you have ordered from the UK? If so then it will have all the fitting instructions in the box with the unit.
The unit will need to be wired into your ECU and the pin outs to be used will be stated in the instruction booklet which comes with the unit. If you have any problems, give me a shout and I'll email a copy over to you. We have been running a group buy on these units over the last two weeks, so have the booklet/instuctions to hand Tina. xx
__________________
Life's not a journey to the grave with the intention of arriving safely in one pretty and well preserved piece, but instead, to skid across the line broadside, thoroughly used up, worn out, leaking oil shouting " GERONIMO " :muhaha:
|
|
#3
03-29-2005, 06:11 PM
|
|||
|
|||
|
That was quick!!
Thanks for the reply,i was kind of hoping i didnt have to wire it into the ecu!! I didnt realise you were doing a group buy or i would have definately got it from you! :x How much were you selling them for if you dont mind me askin
|
|
#4
03-29-2005, 06:12 PM
|
|||
|
|||
|
£272 delivered
__________________
Life's not a journey to the grave with the intention of arriving safely in one pretty and well preserved piece, but instead, to skid across the line broadside, thoroughly used up, worn out, leaking oil shouting " GERONIMO " :muhaha:
|
|
#6
03-29-2005, 06:31 PM
|
|||
|
|||
|
Frazer if you have adobe reader on your pc you can print it from here honey:
http://www.apexi-usa.com/documentation.asp On the left hand side click where it says AVC-R wiring manual then print it off.......... easy as that If you have any problems give me a shout back and i'll email it over to you. Tina. xx
__________________
Life's not a journey to the grave with the intention of arriving safely in one pretty and well preserved piece, but instead, to skid across the line broadside, thoroughly used up, worn out, leaking oil shouting " GERONIMO " :muhaha:
|
|
#7
03-29-2005, 06:41 PM
|
|||
|
|||
|
helpful as ever T
:thumbsup!:
__________________
An evo aint just for Xmas, Its for life :-) Drive it like you stole it! "God gave us children so we could have roses in december!!!!!" I Will Be Home Full Time In September :-) Come On
|
|
#8
03-29-2005, 07:30 PM
|
|||
|
|||
|
i think you could get away with wiring the power and earth, but not totally sure. to be honest, its only 6 (IIRC) wires that need doing so just do the lot. and make sure you wire the purple (IIRC) wire to the rpm feed and NOT the injector feed.
the wiring of it isnt the problem, its the setting up 
|
|
#9
03-29-2005, 08:47 PM
|
|||
|
|||
|
Setting up requires a bit of empty road and half a tank of juice
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
